Rhino-mounts BOOM ARM MOWER DB150 Manuel d'utilisateur Page 154
- Page / 196
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MAINTENANCE
DB150 07/11 Maintenance Section 5-2
©2011 Alamo Group Inc.
MAINTENANCE
HAZARDS WITH MAINTENANCE OF IMPLEMENT
AVOID SERIOUS INJURY OR DEATH FROM COMPONENT FAILURE BY KEEPING IMPLEMENT IN
GOOD OPERATING CONDITION IN PERFORMING PROPER SERVICE, REPAIRS AND
MAINTENANCE.
BEFORE PERFORMING SERVICE, REPAIRS AND MAINTENANCE ON THE IMPLEMENT:
• STOP ENGINE AND PTO, engage parking brake, lower implement, allow all moving parts to stop and remove key before
dismounting from tractor.
•
PLACE implement on ground or securely block up raised equipment. Use large blocks on soft or wet soil.
•
PUSH and PULL Remote Hydraulic Cylinder lever to relieve hydraulic pressure.
•
DISCONNECT Pump solenoid valve or PTO driveline connection before servicing mower head.
•
WEAR SAFETY GLASSES, PROTECTIVE GLOVES and follow SAFETY PROCEDURES when performing service, repairs
and maintenance on the implement:
• Always
WEAR protective GLOVES when handling blades, knives, cutting edges or worn component with sharp edges.
• Always
WEAR GLOVES and SAFETY GLASSES when servicing hot components
•
AVOID CONTACT with hot hydraulic oil tanks, pumps, motors, valves and hose connection surfaces.
•
SECURELY support or BLOCK UP raised implement, framework and lifted components before working underneath equipment.
•
FOLLOW INSTRUCTIONS in maintenance section when replacing hydraulic cylinders to prevent component falling.
•
STOP any implement movements and SHUT-OFF TRACTOR engine before doing any work procedures.
•
USE ladder or raised stands to reach high equipment areas inaccessible from ground.
•
ENSURE good footing by standing on solid flat surfaces when getting on implement to perform work.
•
FOLLOW manufacturer's instructions in handling oils, solvents, cleansers, and other chemical agents.
•
DO NOT change any factory-set hydraulic calibrations to avoid component or equipment failures.
•
DO NOT modify or alter implement, functions or components.
•
DO NOT WELD or repair rotating mower components. These may cause vibrations and component failures being thrown from
mower.
PERFORM SERVICE, REPAIRS, LUBRICATION AND MAINTENANCE OUTLINED IN IMPLEMENT MAINTENANCE
SECTION:
• INSPECT for loose fasteners, worn or broken parts, leaky or loose fittings, missing or broken cotter keys and washers on pins, and
all moving parts for wear.
•
REPLACE any worn or broken parts with authorized service parts.
• Inspect mower blade spindle to ensure bearing preload. If loose repair before operating.
•
LUBRICATE unit as specified by lubrication schedule
•
NEVER lubricate, adjust or remove material while it is running or in motion.
•
TORQUE all bolts and nuts as specified.
BLADE INSPECTION:
• Inspect blade carrier and blades daily.
• Check blade and blade carrier BOLT TORQUE daily. Loose bolts can cause blade or blade bolt failures.
• REPLACE, bent, damage, cracked and broken blades immediately with new blades.
•
AVOID blade failures and thrown broken blades. DO NOT straighten, weld, or weld hard-facing blades.
SAFETY SHIELDS, GUARDS AND SAFETY DEVICES INSPECTION:
• KEEP all Deflectors, Chain Guards, Steel Guards, Gearbox Shields, and PTO integral shields, Bands, Side Skirts and Skid Shoes
in place and in good condition.
•
REPLACE any missing, broken or worn safety shields, guards and safety devices.
• Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of California
to cause cancer, birth defects or other reproductive harm.
• Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the state of California to
cause cancer, birth defects or other reproductive harm.
PN HMBM-01
- OPERATOR’S MANUAL 1
- To the Owner/Operator/Dealer 2
- TABLE OF CONTENTS 7
- SAFETY SECTION 9
- OPERATOR SAFETY 11
- CRUSHING HAZARDS 12
- © 2011 Alamo Group Inc 13
- THROWN OBJECTS HAZARDS 14
- PN TOBM-02 15
- RUN OVER HAZARDS 16
- PTO ENTANGLEMENT HAZARDS 17
- MOWER BLADE CONTACT HAZARDS 18
- HIGH PRESSURE OIL LEAK HAZARD 19
- ELECTRICAL & FIRE HAZARDS 20
- TRANSPORTING HAZARDS 21
- PARTS INFORMATION 23
- Decal Location 23
- TRACTOR / PUMP / CANISTER 24
- TANK / BAR 25
- ROTARY HEAD 26
- Decal Description 27
- Federal Laws and Regulations 38
- Contents 40
- Acknowledgment 40
- Foreword 40
- Safety Alerts 41
- A Word To The User/Operator 41
- Agricultural Disc Mower Types 42
- Follow A Safety Program 43
- Prepare For Safe Operation 47
- Start Safely 51
- Operate Safely 51
- Park Safely 56
- Shut Down Safely 56
- Perform Maintenance Safely 57
- Final Word To The User 64
- Introducción 66
- Contenido 66
- Reconocimiento 66
- Alertas de seguridad 67
- Protéjase a sí mismo 69
- ¡Manténgase alerta! 71
- ¡Manténgase informado! 71
- ¡Tenga cuidado! 71
- Para una operación segura 71
- Conozca las reglas 71
- (continuación) 72
- Conozca los equipos 72
- Arranque con seguridad 77
- Operación con seguridad 77
- Estacionamiento seguro 82
- Apagado con seguridad 82
- Preparación personal 84
- Preparación de la máquina 85
- Riesgos del sistema eléctrico 87
- Evite lesiones 87
- Evite explosiones 88
- INTRODUCTION SECTION 91
- INTRODUCTION 92
- ASSEMBLY SECTION 97
- ASSEMBLY 100
- OPERATION SECTION 107
- OPERATION 108
- MAINTENANCE SECTION 153
- MAINTENANCE 154
- SEGURIDAD 176
- SECCIÓN DE SEGURIDAD 190
- LUBRICACIÓN E HIDRÁULICA 192
- CORTADORA 192
- ACCESORIOS E INSTALACIÓN 192
- ELEMENTOS DE SEGURIDAD 192
- Placa de Número de serie 195
- MANUAL DE OPERADOR 196
Produits connexes et manuels pour Matériel de jardinage Rhino-mounts BOOM ARM MOWER DB150
(194 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.443 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels